Use this handy application guide to find the Jensen Transformers product that is best for your needs.
ISO-MAX Isolator Application Guide
Balanced Audio Isolation and Noise Reduction
Jensen Transformers PI-2XX Stereo Audio Input Isolator
Equipped with Jensen Transformers JT-11P-1 line input transformer, the PI-2XX is ideal for interfacing balanced lines to unbalanced
inputs such as power amplifiers or unbalanced mixer console inputs.
We usually recommend the PI-2XX over the PB-2XX and PO-2XX for most all applications where someone is trying to isolate an audio line.
The PI-2XX is the better choice over the other two models if you need to isolate a high impedance line input, such as the line input of
a power amp or crossover. It will eliminate several types of noise interferences, such as 60 cycle hum, higher frequency buzzes, clicks
& pops from machinery motors, radio station pickup, and noises caused by light dimmers. It needs to be located right at the line inputs,
with a maximum of 3 feet or less of hookup cable on its outputs. The line input it is connected to must have a minimum load impedance of
10k Ohms or higher. There is no restriction to the length of cable on the input side of the PI-2XX.
Jensen Transformers PI-XX Single-Channel Audio Input Isolator
Similar to the the PI-2XX (above), this single-channel version is equipped with Jensen Transformers' JT-11P-1 line input transformer.
Jensen Transformers PO-2XX Stereo Line Output Isolator, 1:1 Output Ratio
The "pro output" model PO-2XX was designed to provide transformer isolation at the output of a device that is driving a long audio cable. Like the PI-2XX and PB-2XX, it allows the full audio frequency range to pass through it, while breaking the physical connection between the source and destination. The 1:1 ratio output type transformer inside has the least passive losses of the three types, and will eliminate 60 Hz ground loop noise. However, since the output transformer does not have an internal Faraday shield like the PI-2XX and PB-2XX, higher frequency "buzz' noises will pass through, making the PO-2XX the least effective of the three for eliminating noise problems. The PO-2XX can be used at either end of a long cable run, but is best used at the start of the run. (Formerly DM2-2XX)
Jensen Transformers PB-2XX Balanced XLR Stereo Audio Input / Output Isolator
The PB-2XX "patch bay" model is the one to choose if you need a general purpose isolation box, especially for sound reinforcement applications. It can tolerate a length of cable on its output side, which would be the case if the PB-2XX was installed in a patch bay either on stage or near a house console. It can connect to a line input that is as low as 600 Ohms input impedance, all the way up to 10k Ohms (or even higher) although it works better into 600 Ohms. Transient response into 10k Ohms is good, although the PI-2XX's response is much better into 10k Ohms. For what it's worth, it would be almost impossible to hear a difference between the two in a live concert application.
The PB-2XX gives you similar rejection of the same noise problems listed above with the PI-2XX, but works only on those noises that get
introduced on the input side of the PB-2XX. If there is a long length of cable on the PB-2XX output, any noises that get picked up on the
output side will not be rejected by the PB-2XX, as they are beyond the box at that point.
The PB-2XX does have internal jumpers that can set each channel individually into a ratio of 1:1, 1:2 step up (approx. 5 dB of signal
gain), or 2:1 step down (approx. 6 dB of signal loss). These internal jumpers are a feature that is unique to the PB-2XX; the other pro
ISO-MAX models do not have internal jumpers. Finally, like the PI-2XX, there is no restriction to the length of cable on the input side of
the PB-2XX.
Unbalanced to Balanced Audio Signal Conversion
Jensen Transformers MEDIA-2 Active Stereo RCA to XLR Converter / Isolator
This 2-channel "Direct Box" is an RCA to XLR (unbalanced to balanced) converter and ground-loop isolator. This versatile interface handles line level and instrument level inputs, converting them to mic level. It can drive cables up to 100 meters (330 feet) in length, while in-built JT-DB-EPC transformers prevent hum-inducing ground loops. The MEDIA-2 also has a 3.5mm mini-TRS input, making it easy to use laptops and mobile devices as sources.
Jensen Transformers PI-2RX Passive Stereo Isolator, 1:1 Output Ratio - RCA to XLR
Configure the PI-2XX with an RCA input and an XLR output and you get the PI-2RX. This configuration is ideal for interfacing
unbalanced sources, such as preamplifiers with RCA outputs, to equipment with balanced inputs such as XLR-equipped power amplifiers.
There is no limit to the length of the cables on the input side of the PI-2RX, although the output cables should be no longer than 3 feet.
PI-Series isolators feature the Jensen Transformers' JT-11P-1 line input transformer, which eliminates noise interferences, such as 60
cycle hum, higher frequency buzzes, clicks & pops from machinery motors, radio station pickup, and light dimmer noise.
Jensen Transformers PI-2RX Mono Isolator, 1:1 Output Ratio - RCA to XLR
Single-channel version of the PI-2RX (above).
Balanced to Unbalanced Signal Conversion
Jensen Transformers PC-2XR Balanced to Unbalanced Audio Converter - XLR to RCA
Featuring a Jensen JT-10KB-D 4 to 1 step-down line input transformer, the PC-2XR works very well in "Pro"(+4dBu) to "Consumer" (-10dBV) level conversion applications. This transformer provides excellent isolation for unbalanced consumer inputs, while also providing the required signal level conversion. (available via the PI-2XX page by choosing the RCA output connectors option)
Speaker Level to Line Level Conversion
Jensen Transformers SP-2SX Stereo Speaker to Line Audio Converter - Speakon to XLR
Jensen Transformers' SP-2SX Stereo Speaker to Line Audio Converter provides audiophile-grade conversion of speaker-level audio to Pro-style XLR balanced line-level audio outputs.
Jensen Transformers SS-2RR Stereo Speaker to Line Audio Converter, tuned specifically for subwoofer inputs - RCA to RCA
Same physical specs as the SC-2NR, but the SS-2NR Stereo Speaker to Line Audio Converter is tuned specifically for subwoofer inputs. Terminal strips inputs and RCA output connectors. (available on the SC-2NR product page)
Jensen Transformers SS-2SX Stereo Speaker to Line Audio Converter, tuned specifically for subwoofer inputs - Speakon to XLR
Same physical specs as the SC-2NR, but the SS-2SX Stereo Speaker to Line Audio Converter is tuned specifically for subwoofer inputs. Speakon inputs and XLR output connectors. (available on the SC-2NR product page)
Unbalanced Audio Isolators (Consumer Interface)
Jensen Transformers CI-1RR Single-Channel Audio Isolator
Equipped with RCA "Consumer Interface" jacks, this audiophile-quality device is suitable for single-channel (mono) full-range unbalanced audio. The CI-1RR not only eliminates hum and buzz, but also enhances audio quality by reducing spectral contamination due to ultrasonic and RF interference. Uses the respectable JT-11P1 line input transformer.
Jensen Transformers CI-2RR Stereo Audio Isolator
All of the advantages of the CI-1RR (above), but with two channels. Perfect for stereo applications. Uses two of the respectable JT-11P1 line input transformers.
Jensen Transformers CI-2MINI Stereo Audio Isolator
Similar to the CI-2RR, but with 3.5mm jacks. Great for iPods, MP3 players, computer audio, or anything that uses 3.5mm interface cables.
Jensen Transformers SUB-1RR Subwoofer/LFE Audio Isolator
Eliminates sub-woofer hum caused by ground differences between equipment. This subwoofer audio isolator is designed specifically as a subwoofer isolator, making it a better choice than for Home Theater and Automotive subwoofer applications than a full-range isolator.
Jensen Transformers SUB-2RR 2-Channel Subwoofer/LFE Audio Isolator
Similar to the model above except that this subwoofer hum isolator can handle two audio channels, the SUB-2RR eliminates sub-woofer hum caused by ground differences between equipment. Designed specifically for sub-woofer amplifier isolation in Home Theater and Automotive applications
Video Signal Isolators
Jensen Transformers VB-1BB Baseband-Composite Video Isolator with BNC Connectors
This ISO-MAX Baseband Video Isolator, which provides 10Hz to 10MHz bandwidth and 120dB of 60Hz Common Mode rejection. This product incorporates true 75 Ohm BNC connectors for low VSWR.
Jensen Transformers VB-1RR Baseband-Composite Video Isolator with RCA Connectors
Eliminates ground-loop-induced hum and noise bars caused by ground differences between equipment. Great for video surveillance systems!
Jensen Transformers VBH-3RR Component Video Ground Loop Corrector
This studio-quality isolator clears up video hum bars caused by ground loops! Available with RCA or BNC connectors.
Jensen Transformers VBH-5BB RGBHV Video Ground Loop Corrector with BNC Connectors
This studio-quality isolator clears up RGB / VGA video hum bars in caused by ground loops.
Cable TV Signal Isolator
Jensen Transformers VRD-1FF Cable TV Ground Loop Isolator
The VRD-1FF CATV Ground Isolator, provides the high 60Hz isolation required to eliminate "ground loops" in Home Theater systems. The 1300MHz bandwidth of the VRD-1FF maintains the high signal quality required for Digital Cable TV and Cable Modem signals. Modem Compatible.